This page was exported from Top Exam Collection [ http://blog.topexamcollection.com ] Export date:Sun Feb 23 19:47:57 2025 / +0000 GMT ___________________________________________________ Title: Real H31-311_V2.5 dumps Accurate Questions and Answers with Free and Fast Updates [Q29-Q50] --------------------------------------------------- Real H31-311_V2.5 dumps Accurate Questions and Answers with Free and Fast Updates Real H31-311_V2.5 Quesions Pass Certification Exams Easily The HCIA-Transmission V2.5 exam covers a wide range of topics related to transmission technologies, including optical fiber transmission, microwave transmission, and access network technologies. H31-311_V2.5 exam is designed to test the candidate's understanding of these technologies, as well as their ability to configure and troubleshoot transmission networks.   NO.29 Which of the following is the main advantage of SDH? (Multiple choice).  standard interface.  Synchronous multiplexing.  Powerful OAM  High compatibility. NO.30 The number of ODU2e signals multiplexed into the ODU3 signal is the same as the number of ODU2 signals multiplexed into the ODU3 signal  yes  False NO.31 Which of the following methods can be used to multiplex low-order ODUK to higher-order ODUk?  Time-division multiplexing  Wavelength division multiplexing  Null division multiplexing  Frequency division multiplexing NO.32 Both PDH and SDH have globally harmonized standards.  True  False NO.33 Which of the following logic function blocks are involved in processing clock signals? (Multiple choice).  SPl  RST  MCF  SETS NO.34 For alignment; Indicates the starting position of VC-n in the corresponding AU or TU frame. * This way: The receiver can correctly remove the corresponding VC from STM-N, and then The VC and C packages are separated into separate low-rate signals, such as PDH, which means that the low-rate path signal can be dropped directly from the STM-N signal.  True  Error NO.35 Which of the following statements about the OTM-n .m and OTMnr .m for OTN are incorrect?  n represents the number of wavelengths carried by the maximum capacity  m indicates the rate. The value can be 1, 2, or 3. .  r represents OTM., which does not have OSC capabilities  OTM-nr .m with OSC signal is OTM-n.m. NO.36 Which of the following is affected by changing the element ID of OSN3500 on NMS?  Interruption of business.  Restart your device.  Network element communication is interrupted.  NE time is out of sync. NO.37 The TAG attribute cannot be set for the internal port VCTRUNK of the single board on the NMS.  True  False NO.38 In WDM systems, it is ideal to use a dielectric thin film filter (TFF) when using less than () wavelengths.  4  8  16  20 NO.39 During service configuration, there are two time slot modes. Huawei uses interleaved time slot mode by default.  True  False NO.40 In the system control unit, which of the following databases does not lose data after a power failure? (Multiple choice).  MDE  DRDB  FDB0  FDB1 NO.41 Which of the following is the steps to multiplex a low-speed service into a high-speed SDH service? (Multiple choice).  Mapping  Overhead insertion  Alignment  Multiplexing NO.42 The device IP address of the gateway element and the non-gateway element must be set in the same network segment.  True  Error NO.43 Which of the following statements regarding the protection of the cross-connecting plate 1+1 is correct? (Multiple choice).  The source business board sends services to the main and standby crossover boards. .  After the service cross-connection is completed, the active and standby cross-board sends the data of the primary cross-board to the receiving service board.  The receiving service board can only receive data from the active cross-link board  The bus of the two cross-connected modules works independently and does not interfere with each other. .  Dual bus system structure indicates that the service board performs dual data transfer to the cross-connection side and selectively receives data on the cross-connection side. .  Both cross-connecting plates have the same configuration. The service board will selectively receive services from one of them based on the quality of service and the status of the cross-connecting board. . NO.44 When using the LCAS function, which of the following overhead bytes is used to transmit control information? (Multiple Choices)  M1  H4  K2  K4 NO.45 Which of the following ITLI-T recommendations define the OTN frame structure?  G.694  G.652  G.975  G.709 NO.46 EPL services use bandwidth exclusively on the line, which is very safe. Dedicated line applications for VIP customers  True  Error NO.47 The following is the frame structure of the STM-16?  9*270*1  9*270″4  9*270*16  9*270*64 NO.48 Which of the following is not an EVPLAN feature?  bandwidth sharing  Forwarding based on MAC address  point-to-point, and point-to-multipoint topologies  Multipoint to multipoint topology NO.49 The OTN signal has a fixed pad period, the same frame period as the SDH signal.  True  False NO.50 Which of the following statements about the EFS4 board are correct? (Multiple choice).  The board has four FE ports. .  The board supports three layers of text exchange. .  The plate must be used with the processing plate.  The board interface is the LC interface.  Loading … H31-311_V2.5 Dumps are Available for Instant Access: https://www.topexamcollection.com/H31-311_V2.5-vce-collection.html --------------------------------------------------- Images: https://blog.topexamcollection.com/wp-content/plugins/watu/loading.gif https://blog.topexamcollection.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-07-12 11:46:31 Post date GMT: 2023-07-12 11:46:31 Post modified date: 2023-07-12 11:46:31 Post modified date GMT: 2023-07-12 11:46:31