This page was exported from Top Exam Collection [ http://blog.topexamcollection.com ] Export date:Mon Jan 20 9:05:46 2025 / +0000 GMT ___________________________________________________ Title: NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions [Q45-Q68] --------------------------------------------------- NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions PDF (New 2023) Actual NACE NACE-CIP1-001 Exam Questions NEW QUESTION 45If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use  a recognized industry standard like SSPC-PA 2 that is broadly accepted  NACE 2/SSPC SP10  their best judgment based on similar projects and specifications.  a detailed checklist and document the lack of a standard. NEW QUESTION 46What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?  1 cm (.39 inch)  2.5 cm (1 inch)  6.35 cm (2.5 inch)  2.5 millimeters (.10 inch) NEW QUESTION 47ISO SA 3 is directly equivalent to:  NACE No. 1/SSPC SP 5  NACE No. 2/SSPC SP 10  NACE No. 3/SSPC SP 6  None of the above NEW QUESTION 48Prior to using Inspection Tools the inspector must:  Ensure the instrument is within calibration parameters  Be trained on how to use the instrument  Read the manufactures’ instructions  a), b) & c) NEW QUESTION 49Relative humidity is  a measure of the amount of moisture in the air compared to saturation level.  a measure of the amount of moisture in the air compared to the air temperature.  the lowest temperature at which moisture forms on a steel surface.  the highest temperature at which moisture forms on a steel surface. NEW QUESTION 50When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:  Pass/fail criteria  A final conflict resolution method  A general guide  A method to grade surface profile NEW QUESTION 51You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners’ representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.As a NACE CIP Level 1 Inspector your preferred course of action is to:  Carefully review the document and do the best you can  Minimize your lack of understanding and go ahead with the inspection task to the best of your ability  Advise the owners’ representative of your lack of knowledge in this area  Hire a third patty to assist you in understanding the document NEW QUESTION 52What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?  70% of the specified maximum thickness  80% of the specified minimum thickness  90% of the specified maximum thickness  100% of the specified maximum thickness NEW QUESTION 53Conventional spray is a good choice when:  High production rates are required  High quality finishes are required  High transfer efficiency is required  High viscosity coatings are being applied NEW QUESTION 54When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:  Use another method as the comparator method is too subjective  Record the segment with the more aggressive profile  Record the segment with the less aggressive profile  Record your result by identifying two segments NEW QUESTION 55When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:  Go with the majority opinion  Never change his/her mind  Achieve consensus through negotiation  Call the supervisor NEW QUESTION 56Stripe coats are best applied by:  Airless spray  Conventional spray  High volume low pressure spray  Brush NEW QUESTION 57ASTM Standards are applicable:  In the USA  In North America  In Asia  When specified NEW QUESTION 58The least effective method of surface cleaning is most likely  water blasting.  dry grit blasting.  hand tool cleaning.  power tool cleaning. NEW QUESTION 59SSPC SP 1 identifies the use of:  Organic solvents  Inorganic solvents  Biodegradable detergents  A wide variety of materials NEW QUESTION 60Removal of surface contaminants is done by:  Abrasive blasting  Waterjetting  A combination of methods  Scarifying NEW QUESTION 61How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?  1  3  5  7 NEW QUESTION 62NACE SP 0178 is a standard for:  Structural steel to be coated for Atmospheric Service  Tanks and Vessels to, be Lined for Immersion Service  Stainless steel pipe to be Externally Coated  Tanks and Vessels to be Externally Coated NEW QUESTION 63You are the NACE Inspector on a job where the Owner’s specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.Your FIRST preferred course of action is to:  Skip the checks as you are. confident the blast pressure is OK  Skip the checks and just record the same readings as you have been getting  Keep doing the checks regardless  Keep doing the checks and consult the Owner’s representative for direction NEW QUESTION 64The main responsibilities of the inspector are to  demonstrate to the contractor how to apply the coating.  observe and direct the work of the contractors.  direct and perform the work stated in the specification.  observe and report the quality of the work performed. NEW QUESTION 65When holiday testing is required the Inspector is always required to enforce NACE SP 0188:  True  False NEW QUESTION 66Whenever dissimilar metals must join, the most common practice is to  provide cathodic protection to prevent corrosion,  provide anodic protection to prevent corrosion.  coat all connected dissimilar metals.  avoid coating all connected dissimilar metals. NEW QUESTION 67Fine cracks in the surface of a coating that rarely reach the substrate are called  cracking.  alligatoring.  checking.  blistering. NEW QUESTION 68Check abrasive blast pressure with a  needle pressure gauge  replica tape  surface comparator  nozzle aperature gauge  Loading … The Coating Inspector Level 1 Exam covers a wide range of topics including surface preparation, coating application, inspection techniques, safety and environmental considerations, and documentation. It is designed to evaluate the competency of the individual in identifying coating defects and recommending appropriate corrective actions. NACE-CIP1-001 exam is a combination of multiple-choice questions and practical assessments that test the individual's ability to apply their knowledge in real-world scenarios. Passing the Coating Inspector Level 1 Exam is a significant achievement and demonstrates a commitment to quality and safety in the coating industry.   Updated Oct-2023 Pass NACE-CIP1-001 Exam - Real Practice Test Questions: https://www.topexamcollection.com/NACE-CIP1-001-vce-collection.html --------------------------------------------------- Images: https://blog.topexamcollection.com/wp-content/plugins/watu/loading.gif https://blog.topexamcollection.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-10-15 12:07:37 Post date GMT: 2023-10-15 12:07:37 Post modified date: 2023-10-15 12:07:37 Post modified date GMT: 2023-10-15 12:07:37