Nov-2023 Download Free Latest Exam 300-710 Certified Sample Questions [Q11-Q31]

November 29, 2023 admin 0 Comments

Rate this post

Nov-2023 Download Free Latest Exam 300-710 Certified Sample Questions

Prepare for your exam certification with our 300-710 Certified Cisco

NEW QUESTION 11
An administrator Is setting up a Cisco PMC and must provide expert mode access for a security engineer. The engineer Is permitted to use only a secured out-of-band network workstation with a static IP address to access the Cisco FMC. What must be configured to enable this access?

Enable SSH and define an access list.

Enable HTTP and define an access list.

Enable SCP under the Access List section.

Enable HTTPS and SNMP under the Access List section.

NEW QUESTION 12
When do you need the file-size command option during troubleshooting with packet capture?

when capture packets are less than 16 MB

when capture packets are restricted from the secondary memory

when capture packets exceed 10 GB

when capture packets exceed 32 MB

NEW QUESTION 13
Drag and drop the steps to restore an automatic device registration failure on the standby Cisco FMC from the left into the correct order on the right. Not all options are used.

Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/firepower_management_center_high_availability.html#id_32288

NEW QUESTION 14
The event dashboard within the Cisco FMC has been inundated with low priority intrusion drop events, which are overshadowing high priority events. An engineer has been tasked with reviewing the policies and reducing the low priority events. Which action should be configured to accomplish this task?

generate events

drop packet

drop connection

drop and generate

NEW QUESTION 15
Drag and drop the steps to restore an automatic device registration failure on the standby Cisco FMC from the left into the correct order on the right. Not all options are used.

Explanation

Explanation
Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/firepower_management_center_high_availability.html#id_32288

NEW QUESTION 16
In a Cisco AMP for Networks deployment, which disposition is returned if the cloud cannot be reached?

unavailable

unknown

clean

disconnected

NEW QUESTION 17
administrator is configuring SNORT inspection policies and is seeing failed deployment messages in Cisco FMC . What information should the administrator generate for Cisco TAC to help troubleshoot?

A Troubleshoot” file for the device in question.

A “show tech” file for the device in question

A “show tech” for the Cisco FMC.

A “troubleshoot” file for the Cisco FMC

NEW QUESTION 18
How many report templates does the Cisco Firepower Management Center support?

unlimited

Section: Management and Troubleshooting
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config-guide- v60/Working_with_Reports.html

NEW QUESTION 19
A network administrator notices that SI events are not being updated The Cisco FTD device is unable to load all of the SI event entries and traffic is not being blocked as expected. What must be done to correct this issue?

Restart the affected devices in order to reset the configurations

Manually update the SI event entries to that the appropriate traffic is blocked

Replace the affected devices with devices that provide more memory

Redeploy configurations to affected devices so that additional memory is allocated to the SI module

NEW QUESTION 20
When do you need the file-size command option during troubleshooting with packet capture?

when capture packets are less than 16 MB

when capture packets are restricted from the secondary memory

when capture packets exceed 10 GB

when capture packets exceed 32 MB

Section: Management and Troubleshooting
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/troubleshooting_the_system.html

NEW QUESTION 21
A Cisco FTD device is running in transparent firewall mode with a VTEP bridge group member ingress interface What must be considered by an engineer tasked with specifying a destination MAC address for a packet trace?

The destination MAC address is optional if a VLAN ID value is entered

Only the UDP packet type is supported

The output format option for the packet logs unavailable

The VLAN ID and destination MAC address are optional

Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/troubleshooting_the_system.html

NEW QUESTION 22
Which license type is required on Cisco ISE to integrate with Cisco FMC pxGrid?

mobility

plus

base

apex

NEW QUESTION 23
Which two routing options are valid with Cisco Firepower Threat Defense? (Choose two.)

BGPv6

ECMP with up to three equal cost paths across multiple interfaces

ECMP with up to three equal cost paths across a single interface

BGPv4 in transparent firewall mode

BGPv4 with nonstop forwarding

Section: Configuration
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/601/configuration/guide/fpmc-config- guide-v601/fpmc-config-guide-v60_chapter_01100011.html#ID-2101-0000000e

NEW QUESTION 24
What is the maximum SHA level of filtering that Threat Intelligence Director supports?

SHA-1024

SHA-4096

SHA-512

SHA-256

NEW QUESTION 25
Which interface type allows packets to be dropped?

passive

inline

ERSPAN

TAP

Reference:
https://www.cisco.com/c/en/us/support/docs/security/firepower-ngfw/200908-configuring-firepower-threat-defense-int.html

NEW QUESTION 26
An engineer is configuring a cisco FTD appliance in IPS-only mode and needs to utilize fail-to-wire interfaces. Which interface mode should be used to meet these requirements?

transparent

routed

passive

inline set

NEW QUESTION 27
Drag and drop the steps to restore an automatic device registration failure on the standby Cisco FMC from the left into the correct order on the right. Not all options are used.

NEW QUESTION 28

Refer to the exhibit. An engineer is analyzing the Attacks Risk Report and finds that there are over 300 instances of new operating systems being seen on the network. How is the Firepower configuration updated to protect these new operating systems?

The administrator manually updates the policies.

The administrator requests a Remediation Recommendation Report from Cisco Firepower.

Cisco Firepower gives recommendations to update the policies.

Cisco Firepower automatically updates the policies.

Section: Management and Troubleshooting

NEW QUESTION 29
What is the result of specifying of QoS rule that has a rate limit that is greater than the maximum throughput of an interface?

The rate-limiting rule is disabled.

Matching traffic is not rate limited.

The system rate-limits all traffic.

The system repeatedly generates warnings.

Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/quality_of_service_qos.pdf

NEW QUESTION 30
What is the maximum bit size that Cisco FMC supports for HTTPS certificates?

1024

8192

4096

2048

Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/610/configuration/guide/fpmc-config-guide-v61/system_configuration.html

NEW QUESTION 31
In a Cisco AMP for Networks deployment, which disposition is returned if the cloud cannot be reached?

unavailable

unknown

clean

disconnected

Section: Integration
Explanation/Reference:

Loading …

Cisco 300-710 (Securing Networks with Cisco Firepower) certification exam is designed to test the knowledge and skills of network security professionals who use Cisco Firepower Next-Generation Firewall (NGFW), web security, and email security appliances. 300-710 exam focuses on the deployment, configuration, and management of Cisco Firepower NGFW, including its integration with other Cisco security solutions. Securing Networks with Cisco Firepower certification is intended for security engineers, network designers, and administrators who want to enhance their knowledge and skills in network security.

Obtaining the Cisco 300-710 certification validates the skills and knowledge of network security professionals in deploying and managing Cisco Firepower NGFW and its associated security solutions. Securing Networks with Cisco Firepower certification can increase job opportunities and enhance career growth for professionals in the network security field. It also helps organizations ensure that their network security professionals have the necessary skills to secure their networks against modern security threats.

Free Cisco 300-710 Exam 2023 Practice Materials Collection: https://www.topexamcollection.com/300-710-vce-collection.html

300-710 Practice Tests

Nov-2023 Download Free Latest Exam 300-710 Certified Sample Questions [Q11-Q31]

Related Certifications

200-201
200-301
300-815
350-701
300-825
300-730
300-440
700-755
300-415
500-220