2023 300-410 Dumps PDF - 300-410 Real Exam Questions Answers [Q155-Q169]

2023 300-410 Dumps PDF – 300-410 Real Exam Questions Answers [Q155-Q169]

October 25, 2023 admin 0 Comments

Rate this post

2023 300-410 Dumps PDF – 300-410 Real Exam Questions Answers

Valid 300-410 Test Answers & Cisco 300-410 Exam PDF

Candidates who pass the Cisco 300-410 certification exam will gain a deep understanding of advanced routing and services technologies, which will help them to design, implement, and troubleshoot complex enterprise networks. Implementing Cisco Enterprise Advanced Routing and Services certification is highly valued by employers, as it demonstrates that the holder has the skills and knowledge required to work with advanced routing and services technologies.

Cisco 300-410 exam is part of the Cisco Certified Specialist – Enterprise Advanced Infrastructure Implementation certification, which is designed for IT professionals who want to validate their skills in implementing advanced routing technologies and services in enterprise networks. 300-410 exam covers a wide range of topics related to enterprise routing and services, including advanced routing protocols, quality of service (QoS), virtual private networks (VPNs), and network automation.

Q155.

Refer to the exhibit A company builds WAN infrastructure between the head office and POPs using DMVPN hub-and-spoke topology to provide end-to-end communication All POPs must maintain point-to-point connectivity with the head office Which configuration meets the requirement at routers R12 and R13?

Option A

Option B

Option C

Option D

Q156. Refer to the exhibit.

Which statement about R1 is true?

OSPF redistributes RIP routes only if they have a tag of one.

RIP learned routes are distributed to OSPF with a tag value of one.

R1 adds one to the metric for RIP learned routes before redistributing to OSPF.

RIP routes are redistributed to OSPF without any changes.

Q157. Refer to the exhibit.

Which two actions restrict access to router R1 by SSH? (Choose two.)

Configure transport input ssh on line vty and remove sequence 30 from access list 100.

Configure transport output ssh on line vty and remove sequence 20 from access list 100.

Remove class-map ANY from service-policy CoPP

Configure transport output ssh on line vty and remove sequence 10 from access list 199.

Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list
199

Q158. Refer to the exhibit.

Which action makes 10.1.3.2 the feasible successor to reach 10. 200. 1 0/24 for location S42T447E33F95?

Increase path bandwidth lower than 1011 2 and lower than 1012 2 between RtrA and the destination

Increase path bandwidth higher than 10.1 2 2 and lower than 101.1.2 between RtrA and the destination.

Increase path bandwidth higher than 1011 2 and lower than 1012 2 between RtrA and the destination

Increase path bandwidth higher than 10.1 2 2 and higher than 10.1.1.2 between RtrA and the destination

Q159. An engineer configured Reverse Path Forwarding on an interface and noticed that the routes are dropped when a route lookup fails on that interface for a prefix that is available in the routing table Which interface configuration resolves the issue?

ip verify unicast source reachable-via rx

ip verify unicast source reachable-via any

ip verify unicast source reachable-via allow-default

ip verify unicast source reachable-via 12-src

According to this question, uRPF is running in strict mode because packets are dropped even when that route exists in the routing table. Maybe packets are dropped because the receiving interface is different from the interface the local router uses to send packets to that destination.
The ip verify unicast source reachable-via rx command enables Unicast RPF in strict mode.
To enable loose mode, administrators can use the any option (ip verify unicast source reachable-via any). In loose mode, it doesn’t matter if we use this interface to reach the source or not.

The allow-default option allows the use of the default
route in the source verification process.

Q160. Refer to the exhibits.

Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two commands are missing? (Choose two.)

The ip nhrp redirect command is missing on the spoke routers.

The ip nhrp shortcut command is missing on the spoke routers.

The ip nhrp map command is missing on the hub router.

The ip nhrp shortcut command is missing on the hub router.

The ip nhrp redirect command is missing on the hub router.

Q161.

Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?

10.2.2.0/24

10.1.4.0/26

10.1.2.0/24

10.2.3.0/26

Section: Layer 3 Technologies

Q162. An engineer configured a router with this configuration
ip access-hst DENY TELNET
10 deny tcp any any eq 23 log-input
The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet” Which action stops messages on the console while still denying Telnet?

Configure a 20 permit ip any any command

Remove log-Input keyword from the access list.

Replace log-input keyword with the log keyword in the access list.

Configure a 20 permit ip any any log-input command.

Q163. Refer to the exhibit.

An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?

flow monitor Flowmonitor1
destination 10.221.10.11

flow exporter FlowAnalyzer1
destination 10.221.10.11

interface Ethernet0/1
flow-destination 10.221.10.11

interface Ethernet0/0
flow-destination 10.221.10.11

Q164. Which is statement about IPv6 inspection is true?

It teams and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables

It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables

It teams and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables

It team and secures binding for stateless autoconfiguration addresses in Layer 2 neighbor tables.

Q165. Refer to Exhibit.

A network administrator added one router in the Cisco DNA Center and checked its discovery and health from the Network Health Dashboard. The network administratorobserved that the router is still showing up as unmonitored. What must be configured on the router to mount it in the Cisco DNA Center?

Configure router with NetFlow data

Configure router with the telemetry data

Configure router with routing to reach Cisco DNA Center

Configure router with SNMPv2c or SNMPv3 traps

Unmonitored: Unmonitored devices are devices for which Assurance did not receive any telemetry data during the specified time range.

Q166. Drag and drop the MPLS VPN device types from me left onto the definitions on the right.

Q167. Which method provides failure detection in BFD?

short duration, high overhead

short duration, low overhead

long duration, high overhead

long duration, low overhead

Q168. Refer to the exhibit.

An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP. where the metric must be added when traversing through multiple hops to start an external route of 20 The engineer notices that the external metric is fixed and does not add at each hop. Which configuration resolves the issue?

Option A

Option B

Option C

Option D

Q169. Refer to the exhibit.

The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?

Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2

Set OSPF cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2

Set OSPF cost 200 at Site: A RTR1 and set OSPF Cost 100 at Site-B RTR2

Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2

Explanation
OSPF type 1 route is always preferred over a type 2 route for the same destination so we can set metric-type 1 at Site-A RTR1 so that it is preferred over Site-B RTR2.
Note:
Routes are redistributed in OSPF as either type 1 (E1) routes or type 2 (E2) routes, with type 2 being the default.
– A type 1 route has a metric that is the sum of the internal OSPF cost and the external redistributed cost.
– A type 2 route has a metric equal only to the redistributed cost.
– If routes are redistributed into OSPF as type 2 then every router in the OSPF domain will see the same cost to reach the external networks.
– If routes are redistributed into OSPF as type 1, then the cost to reach the external networks could vary from router to router.

Loading …

300-410 Exam Dumps – PDF Questions and Testing Engine: https://www.topexamcollection.com/300-410-vce-collection.html

300-410 Practice Tests

2023 300-410 Dumps PDF – 300-410 Real Exam Questions Answers [Q155-Q169]

Related Certifications

700-846
200-301
300-825
100-890
300-815
300-415
700-755
200-901
350-501
300-715