350-501 Actual Questions Answers PDF 100% Cover Real Exam Questions [Q98-Q116]

July 31, 2024 admin 0 Comments

Rate this post

350-501 Actual Questions Answers PDF 100% Cover Real Exam Questions

350-501 Exam questions and answers

Cisco 350-501 certification exam consists of multiple-choice questions that test the knowledge and skills of the candidates in various areas of service provider network core technologies. 350-501 exam covers topics such as network architecture and design, virtualization, automation, network assurance, security, and services. 350-501 exam is designed to test the candidates’ ability to design and deploy service provider networks, troubleshoot network issues, and ensure network security.

NEW QUESTION 98
Refer to the exhibit:

In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1. 2. and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

NEW QUESTION 99
Refer to the exhibit.

An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
A)

B)

C)

Option A

Option B

Option C

Option D

NEW QUESTION 100
Refer to the exhibit. An engineer started to configure a router for OSPF. Which configuration must the engineer perform on the router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?

router(config)# router ospf 11router(config-if)# no passive-interface ethernet 1/1

router(config)# interface ethernet 1/1router(config-if)# no shutdown

router(config)# interface ethernet 1/1router(config-if)# ip ospf hello-interval

router(config)# interface ethernet 1/1router(config-if)# ip ospf priority 0

NEW QUESTION 101
You are writing an RPL scnpt to accept routes only from certain autonomous systems Consider this code.

If you apply this code to BGP filters, which effect does the code have on your router?

denies routes from AS 7070

allows routes from AS 7077

denies routes from AS 7007

allows routes from AS 770

NEW QUESTION 102
DRAG DROP
Drag and drop the OSPF area types from the left onto the correct statements on the right.
Select and Place:

Section: Networking

NEW QUESTION 103
Which configuration modifies Local Packet Transport Services hardware policies?

https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-1/addr_serv/command/reference/b_ipaddr_cr41crs/b_ipaddr_cr41crs_chapter_0111.html#wp1754734006

NEW QUESTION 104
Refer to the exhibit.

While troubleshooting the OSPF adjacency between routers R1 and R2 an engineer noticed that both routers are stuck in the EXCHANGE/EXSTART state. What should the engineer fix to solve the ongoing issue?

match IPv4 addresses

match OSPF areas

match OSPF network types

match MTU values

NEW QUESTION 105
Refer to the exhibit:

An engineer is preparing to implement link aggregation configuration.
Which statement al about this configuration is true?

The switch port actively sends packets to negotiate an EtherChannel using PAgP

The switch port accepts LACP and PAgP packets from a connected peer and negotiate an EtherChannel using the common EtherChannel mode.

The switch port passively negotiates an EtherChannel if it receives PAgP packets from a connected peer

The switch port negotiates an EtherChannel if it receives LACP packets from a connected peer

NEW QUESTION 106
Refer to the exhibit.

What is the effect of this configuration?

R1 supports a graceful restart operation on the peer, even if graceful restart is disabled on the peer.

R1 supports a peer that is configured for LDP SSO/NSF as the peer recovers from an outage.

R1 failovers only to a peer that is configured for LDP SSO/NSF.

R1 failovers to any peer.

NEW QUESTION 107
An operations engineer must implement IPv6 multicast leveraging the multicast group address FF70::/12.
Which two Cisco IOS XE configurations are needed to accomplish this task? (Choose two.)

Apply the ipv6 mid ssm-map enable and ipv6 mid ssm-map static commands only on the RP IPv6 router.

Apply the ipv6 pim command in all interfaces of all IPv6 routers in the IPv6 multicast domain.

Apply the ipv6 multicast-routing command in all IPv6 routers in the IPv6 multicast domain.

Apply the ipv6 pim rp-address command only on RP IPv6 router.

Apply the ipv6 pim bsr candidate rp command on the IPv6 routers that announce themselves as RPs and the ipv6 pim bsr candidate bsr command on mapping agent routers only.

NEW QUESTION 108
Refer to the exhibit:

A network operator working for service provider with an employee id 3715 15:021 applied this configuration to a router.
Which additional step should the engineer use to enable LDP?

Disable Cisco Express Forwarding globally

Delete the static router ID

Enable MPLS LDP on the interface

Configure the both keyword to enable LDP globally

NEW QUESTION 109
Refer to the exhibit. The USER that is connecting an application on an Internet connection in AS
100 is facing these issues:
– The USER lost the connection to the application during a failure
between IG and R2.
– Router R2 configuration is lost due to a power outage.
– The application the USER is connecting to is hosted behind CE2.
What action resolves the issues on R3 and R4 routers?

Set R4 as a route reflector for R3 and CE2

Apply high Local Preference on R3 toward R1

Set R3 as a route reflector for R4 and CE1

Apply low Local Preference on R4 toward R2.

NEW QUESTION 110
Refer to the exhibit:

Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?

The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family

The neighbor relationship is down because R1 believes R2 is in AS 65012.

The neighbor relationship is up

The neighbor relationship is down because the loco I-as value for R2 is missing in the R1 neighbor statement

NEW QUESTION 111
Refer to the exhibit:

What does this value mean when it is received in XML?

It shows the ending of the script

It indicates a break in a sequence

It indicates a value assigned by a network administrator to tag a route

It means a data field is blank

NEW QUESTION 112

Refer to the exhibit. Based on the show command output, which result is true after BGP session is established?

The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2.

The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from
192.168.2.2.

No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it.

The IOS XR router does not advertises any routes to the neighbor 192.168.2.2, but it accepts any routes from 192.168.2.2.

Section: Networking
Explanation/Reference:

NEW QUESTION 113
Refer to the exhibit:

A network engineer is implementing a BGP protocol. Which effect of the local-as keyword in this configuration is true?

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 without additional configuration

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 without additional configuration.

The local-as keyword is used in BGP configurations to change the local AS number that is used in the BGP OPEN message when establishing a BGP session with a specific neighbor. In this case, even though the router is configured with AS 65000, it will use AS 65112 when establishing a connection with neighbor 192.168.1.2 due to the local-as keyword configuration. Reference := Cisco
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13761-39.html

NEW QUESTION 114
Refer to the exhibit:

What is the effect of this configuration?

The two routers fail to form a neighbor relationship because their system IDs are different.

The two routers successfully form a neighbor relationship

The two routers fail to form a neighbor relationship because the authentication configuration is missing

The two routers fail to form a neighbor relationship because they have different ISIS area types.

NEW QUESTION 115
An engineer working for telecommunication company with an employee id: 3715 15 021 needs to secure the LAN network using a prefix list Which best practice should the engineer follow when he implements a prefix list?

An engineer must use non sequential sequence numbers in the prefix list so that he can insert additional entries later.

The final entry in a prefix list must be /32

An engineer must identity the prefix list with a number only

An engineer must include only the prefixes for which he needs to log activity.

NEW QUESTION 116
Refer to the exhibit. In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1, 2, and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

Loading …

Cisco 350-501 exam is designed for professionals who wish to validate their skills in implementing and operating core technologies in a service provider network. 350-501 exam is a part of the CCNP Service Provider certification and tests the candidate’s knowledge of advanced routing protocols, MPLS VPNs, QoS, and network automation. Passing 350-501 exam will demonstrate that the candidate has the expertise required to work with complex service provider networks.

TopExamCollection 350-501 Exam Practice Test Questions: https://www.topexamcollection.com/350-501-vce-collection.html

350-501 Practice Tests

[Q123-Q145] Latest Cisco 350-501 First Attempt, Exam real Dumps Updated [Aug-2022]
350-501 Actual Questions Answers PDF 100% Cover Real Exam Questions [Q98-Q116]

Related Certifications

500-442
200-201
300-710
700-805
100-890
500-220
300-730
700-755
300-515
300-435