Free JN0-104 Exam Files Downloaded Instantly 100% Dumps & Practice Exam [Q122-Q144] : Top Exam Collection : http://blog.topexamcollection.com

Q122. Which character in the Junos software CLI allows you to filter and manipulate command output?

question mark

pipe character

Q123. What are three Application Layer protocols? (Choose three.)

DNS

TCP

HTTP

ファイル転送プロトコル

ATM

Q124. What are the commands when configuring an IP Address for a Fast Ethernet Interface? (Choose two)

set interfaces fe-0/0/0 address 10.1.1.1/24

set interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24

set interfaces fe-0/0/0.0 family inet address 10.1.1.1/24

set interfaces fe-0/0/0.0 address 10.1.1.1/24

Q125. What is the decimal equivalent of 00000100?

Q126. Which configuration command can you use to reset a Junos device to factory defaults?

reset configuration

load factory-default

load override default

set default configuration

Q127. Click the Exhibit button

A packet destined to the 172.27. 102.65 IP address is received by the ge-0/0/1.0 interface on your Junos device. The input firewall filter shown in the exhibit is applied to the ge-0/0/1.0 interface.
Which two actions are performed in this scenario? (Choose two.)

The packet is logged

The packet is accepted

The packet is counted

The packet is discarded.

Q128. 出展ボタンをクリックします。

You want to make the OSPF route shown in the exhibit the active route for the 10.10.10.0/24 IP address.
Which action is required to accomplish this task?

Set the static route to no-readvertise.

Set the OSPF route preference to 4.

Set the static route preference to 0

Set the OSPF metric to 0

Q129. Which of these protocol daemons is responsible for routing protocols?

dcd

syslogd

rpd

chassisd

Q130. Which two protocols use UDP as a transport protocol by default? (Choose two)

リップ

ディーエイチシーピー

アイシーエムピー

テルネット

Q131. Which of these is true when the following command is issued?
ping interface ge-0/0/0 192.168.1.1 bypass-routing count 1000 rapid

The count parameter creates a counter that you can view with the show firewall command.

The count parameter allows the router to send out 1000 pings and then stop.

The count parameter allows the router to pause for 1000 seconds before sending a ping.

The count parameter allows the router to count the number of pings for logging purposes.

Q132. Which user authentication method is supported by Junos as a last resort alternative?

ラディアス

local user database

CHAP

TACACS+

Q133. You must segment your internal 192.168.1.0/24 network into a minimum of 12 subnets, each containing a minimum of 12 hosts.
Which network mask do you use?

/26

/27

/28

/29

Q134. Which statement is correct about the validate option when upgrading JUNOS software with the request system software add command?

It will check the compatibility of the configuration with the install package.

It will check if the device meets the storage requirement for the install package.

It will check the MD5 checksum of the install package.

It will check if the device meets the memory requirements for the install package.

Q135. What are two benefits of class of service (CoS)? (Choose two.)

CoS can increase the performance of a slow network.

CoS can manage traffic congestion

CoS can prioritize latency-sensitive traffic

CoS can increase network bandwidth.

Q136. Which two statements describe the connection between control plane and forwarding plane? (Choose two.)

No rate limiter is configured by default.

A rate limiter is configured by default.

Exception traffic is preferred over the control traffic during congestion.

Control traffic is preferred over the exception traffic during congestion.

Q137. You issue a “request system zeroize” command. Which statement is correct in this scenario?

All data files remain unchanged but all configuration settings returned to factory defaults.

All data files are deleted and all configuration settings are returned to factory defaults.

All data files are deleted and all configuration settings remain unchanged

Disk space is freed by rotating log files and a proposed list of files to be deleted is presented.

Q138. During a password recovery, what is the next step after configuring the system to boot into single-user mode?

Type recovery.

Press the space bar.

Press the “Enter” Key.

Reset the password.

Q139. Which of these commands can be used to load the rescue configuration?

rollback rescue

commit rescue

load rescue

rollback 49

Q140. Which of these about routing tables are true? (Choose two)

Information learned from routing protocols is stored in the routing table.

Routing table is populated from the forwarding table.

Multiple routing tables can be configured on Junos devices.

The default IPv4 unicast routing table is inet.4

Q141. 出展する：

Which type of route does the configuration create?

an indirect next hop

a generated route

a non-advertised route

a default gateway

Q142. What are two logical interface properties? (Choose two.)

duplex

IPアドレス

DLCI

speed

Q143. Which two Junos product lines are used primarily for security? (Choose two.)

J Series

SRX Series

PTX Series

QFX Series

Q144. Which of these commands can be used to ping from the configuration mode?

user@router# ping 192.168.1.1

user@router# try ping 192.168.1.1

user@router# do ping 192.168.1.1

user@router# run ping 192.168.1.1

無料JN0-104試験ファイルは、即座に100%ダンプ＆プラクティス試験[Q122-Q144]をダウンロードした。

Juniper JN0-104 Exam Syllabus Topics: