Released Fortinet NSE6_FSW-7.2 Updated Questions PDF [Q13-Q31] : Top Exam Collection : http://blog.topexamcollection.com

Q13. What are two reasons why time synchronization between FortiGate and its managed FortiSwitch is critical in switch management? (Choose two.)

FortiSwitch does not retain its time after a reboot, which gets reset after each reboot.

FortiSwitch will not be able to become an NTP server for downstream devices.

FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel.

FortiSwitch will not allow other FortiSwitch devices in the chain be discovered by FortiGate.

Q14. In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Switch the FortiLink interface to the target VDOM.

Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

Q15. FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

The handshake process timed out before FortiSwitch responded.

DTLS client hello had the incorrect pre-shared key.

The CAPWAP tunnel failed to come up due to a mismatch in time.

FortiSwitch has disabled FortiLink and is only managed as a standalone.

Q16. How does FortiSwitch perform actions on ingress and egress traffic using the access control list (ACL)?

Only high-end FortiSwitch models support ACL.

ACL can be used only at the prelookup stage in the traffic processing pipeline.

Classifiers enable matching traffic based only on the VLAN ID.

FortiSwitch checks ACL policies only from top to bottom.

Q17. 展示を参照。

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

Maximum value to accept clients DHCP request is configured as per DHCP server range.

FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.

DHCP clients that are trusted by DHCP snooping configured is only one.

Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.

Q18. To enhance service in emergency situations, to which LLDP-MED Type-Length-Values does Forti-Switch advertise to IP phones?

Network policy

Inventory management

所在地

Power management

Q19. Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Create an SNMP user to use for authentication and encryption.

Specify an SNMP host to send traps to.

Enable an SNMP v3 to handle traps messages with SNMP hosts.

Configure SNMP agent and communities.

Q20. Refer to the configuration:

Which two conditions does FortiSwitch need to meet to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces

FortiSwitch would need to be rebooted.

The split port can be assigned to a native VLAN.

The Dort full speed prior to the split was 100G QSFP+.

Q21. Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?

Tail-drop mode

Weighted round robin mode.

Random early detection mode

Strict mode

Q22. Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?

SPAN

Sniffer profile

sFlow

TCP dump

Q23. Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?

lt is a scalable and secure solution in comparison to other Layer 2 security measures.

FortiSwitch uses only the Ethernet type to assign traffic to VLANs.

It provides benefits that can be obtained when using 802.1X authentication.

Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.

Q24. 展示を参照。
The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

Assign a new LL0P profile to handle different LLDP-ME0 TLVs

Add power management as part of LLDP-MED TLVs to advertise.

Define an LLDP-ME0 location 10 to use standard protocols for power.

Create new a LLOP-MEO application type to define the PoE parameters.

Q25. 出展する。

Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?

Create a new local access profile for SNMP only.

Enable SNMP on the internal interface of the switch.

Configure an SNMP host to send SNMP traps.

Add SNMP service on the management interface of the switch.

Q26. 出展する。

LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)

Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group

Switch 3 and Switch 4 uplinks are treated as single interfaces.

Switch 3 and switch 4 are seen as one MCLAG switch client

Switch 1 and Switch 2 both seen as one single switch.

Q27. 展示を参照。

Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)

FortiSwitch is sending FortiLink heartbeats to FortiGate.

FortiSwitch is discovered and authorized by FortiGate.

FortiSwitch is in a waiting state to join the stack group on FortiGate.

FortiSwitch is ready to push its new hostname to FortiGate.

Q28. Which two statements about the FortiLink authorization process are true? (Choose two.)

The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.

FortiSwitch requires a reboot to complete the authorization process.

A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.

FortiLink authorization sets the FortiSwitch management mode to FortiLink.

Q29. Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

All ports have auto-discovery enabled by default.

No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

The last four switch ports on FortiSwitch have auto-discovery enabled by default.

Q30. Which QoS mechanism maps packets with specific CoS or DSCP markings to an egress queue?

Queuing for egress traffic

Classification for ingress traffic

Rate limiting for egress traffic

Marking for ingress traffic

Q31. 展示品を参照。

Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

port1 was shut down by loop guard protection.

STP triggered a loop and applied loop guard protection on port1.

An endpoint sent a BPDU on port1 that it received from another interface.

Loop guard frame sourced from port 1 was received on port 1.

Fortinet NSE6_FSW-7.2更新問題集PDF [Q13-Q31]をリリースしました。