PDF Download Free of HPE6-A72 Valid Practice Test Questions [Q60-Q84]

HPE6-A72 유효 모의고사 문제 [Q60-Q84] PDF 무료 다운로드

11월 19, 2024 관리자 0 댓글

이 게시물 평가하기

PDF Download Free of HPE6-A72 Valid Practice Test Questions

HPE6-A72 Test Engine files, HPE6-A72 Dumps PDF

HP HPE6-A72 certification exam is an excellent opportunity for network professionals who want to demonstrate their skills and knowledge in the area of Aruba switching. Aruba Certified Switching Associate Exam certification is highly respected in the IT industry and provides a range of benefits for certified professionals. If you are interested in pursuing a career in Aruba switching, the HPE6-A72 exam is an excellent place to start.

HP HPE6-A72 certification exam is an excellent way to demonstrate your commitment to your profession. By passing HPE6-A72 exam, you will show that you have the skills and knowledge necessary to perform the duties of an Aruba Certified Switching Associate. Aruba Certified Switching Associate Exam certification is recognized globally and is highly respected in the industry. It will give you a competitive edge in the job market and help you advance in your career.

새 질문 60
What is the Link Layer Discovery Protocol?

a discovery protocol used between Layer 3 devices to determine routes within a single autonomous system

a standardized IPv6 neighbor discovery protocol used to replace the ARP and broadcast mechanism used in IPv4

a standardized protocol for communicating directly-connected device information and capabilities.

an Aruba proprietary discovery protocol supported in all Aruba switches along with Cisco Discovery Protocol or CDP

새 질문 61
Place the OSI Layers in the correct order. Arrange them from least to greatest, starting with Layer 1 on the top, and progressing to Layer 7 on the bottom.

설명:
그래픽 사용자 인터페이스, 애플리케이션 설명 자동 생성

새 질문 62
전시회를 참조하세요.

What is the correct binary conversion of the last two hexadecimal characters of the physical address?

1101 1000

1110 1101

1001 1111 0101 0011

1000 1101 1110 1101

새 질문 63
Which two port characteristics must match between LAG interfaces? (Choose two.)

Port number

Duplex

Member ID

Media type

Chassis number

새 질문 64
전시회를 참조하세요.

What commands will successfully enable the SVI for vlan 100 on interface 1/1/1 to produce the results displayed in the commandshow ip interface briefin the exhibit below?

Access-1(config)# interface 1/1/1
Access-1(config-if)# routing
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24

Access-1(config)# interface 1/1/1
Access-1(config-if)# vlan trunk permit vlan 100
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address static 10.1.1.1/24

Access-1(config)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24

Access-1(config-if)# vlan 100
Access-1(config-vlan)# ip address 10.1.1.1/24

새 질문 65
Click on the colored box that corresponds with the line that best represents Multicast traffic flow.

설명:
Diagram Description automatically generated

Blue Box

새 질문 66
What are two key features unique to AOS-CX that support root cause analytics and recovery in a wired network? (Select two.)

REST APIs

Network Analytics Engine

Multi-Protocol Border Gateway Protocol (MP-BGP)

Redundant management modules

Checkpoints

새 질문 67
Review the exhibit.
As the frame traverses from **PC-1** to **Server-1**, the VLAN tag will be removed.
Click on the interface (circled in green) where the VLAN tag will be removed.

설명:
Diagram Description automatically generated

Port 1/1/4 on Access-2.

새 질문 68
전시회를 참조하세요.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?

Access-2# configure
Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2

This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

새 질문 69
Interface 1/1/1 is up
Admin state is up
Link transitions: 1
Description: TO_PC-1
Hardware: Ethernet, MAC Address: 00:11:22:33:44:55
MTU 1500
Type 1GbT
Full-duplex
qos trust none
Speed 1000 Mb/s
Auto-negotiation is on
Flow-control: off
Error-control: off
MDI mode: MDIX
VLAN Mode: access
Access VLAN: 1111
Which command will produce the above output?

show interface vlan 1111

show interface 1/1/1

show interface gigabit 1/1/1

show vlan 1111

새 질문 70
Match the terms to the correct layer of the OSI model.

새 질문 71
Match each description to the correct management tool for Aruba AOS-CX.

새 질문 72
The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output ofshow vlanwith no other vlan commanded having been added?

옵션 A

옵션 B

옵션 C

옵션 D

새 질문 73
전시회를 참조하세요.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master. What is a valid configuration for Access-2 to join the VSF stack?

Access-2# configure
Access-2(config)# vsf member 1
Access-2(config)# vsf renumber-to 2
Access-2(vsf-member-1)# link 2 2/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 1
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
Access-2(config)# vsf renumber-to 2
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

Access-2# configure
Access-2(config># vsf member 2
Access-2(vsf-member-1)# link 2 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

새 질문 74
Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.

새 질문 75
전시회를 참조하십시오.

What is true regarding VLAN 50 according to the diagram above?

VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

VLAN 50 was never added to the vlan-database and therefore is in a down state.

새 질문 76
전시회를 참조하세요.

All switches are running Aruba OS-CX. While working in the terminal of Access-2, you are unable to reach Server-1 using SSH.
What is the correct command to ping Server-1 from Access-2 to test reachability?

Access-2# ping6 172.16.1.97 vrf mgmt.

Access-2# ping 172.16.1.97

Access-2# ping 172.16.1.97 vrf default

Access-2# ping 172.16.1.97 vrf mgmt

새 질문 77
The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

새 질문 78
The following command is issued:
Switch# checkpoint rollback start
결과는 어떻게 되나요?

The command will fail because rollback commands must be issued from global-config mode.

The switch will revert the running-configuration to the checkpoint called ‘start1 without a reboot.

The command will fail because it is incomplete.

The switch will use the checkpoint ‘rollback1 as the starting configuration on next reboot.

새 질문 79
전시회를 참조하세요.

Refer to the diagram where all switches are CX 6300Ms. Which MSTP configuration should be applied to Core-2 in order for Core-2 to join the domain as the primary for Instance 2 and secondary for Instance 1?

A close-up of words Description automatically generated

A black text on a white background Description automatically generated

새 질문 80
Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

UDP 1812 and UDP 1813

UDP 161

TCP 443

UDP 162

새 질문 81
Which command will suppress LLDP messages from egressing on a given port while still allowing LLDP to be enabled on the switch?

switch(config-if)# no lldp interface (port) transmit

switch(config-if)# no lldp transmit

switch(config-if)# no lldp receive

switch(config)# no lldp

새 질문 82
What command displays information regarding the secondary image installed on an AOS-CX switch?

show secondary

show version detail

show version

show images

새 질문 83
What are two available options as part of a DHCP offer message? (Choose two.)

SSID

DNS server IP

Subnet Mask

LLDP-MED

VLANID

새 질문 84
What is the process where a compute device converts logical data bits into the correct physical representation depending on the media?

Demodulation

Modulation

Propagation

Encapsulation

로드 중 …

Pass Your Aruba Certified Switching Associate (ACSA) V1 HPE6-A72 Exam on Nov 19, 2024 with 107 Questions: https://www.topexamcollection.com/HPE6-A72-vce-collection.html