350-501 Actual Questions Answers PDF 100% Cover Real Exam Questions [Q98-Q116]

350-501 실제 문제 답안 PDF 100% 커버 실제 시험 문제 [Q98-Q116]

7월 31, 2024 관리자 0 댓글

이 게시물 평가하기

350-501 Actual Questions Answers PDF 100% Cover Real Exam Questions

350-501 Exam questions and answers

Cisco 350-501 certification exam consists of multiple-choice questions that test the knowledge and skills of the candidates in various areas of service provider network core technologies. 350-501 exam covers topics such as network architecture and design, virtualization, automation, network assurance, security, and services. 350-501 exam is designed to test the candidates’ ability to design and deploy service provider networks, troubleshoot network issues, and ensure network security.

새 질문 98
전시회를 참조하세요:

In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1. 2. and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

새 질문 99
전시회를 참조하세요.

An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
A)

B)

C)

옵션 A

옵션 B

옵션 C

옵션 D

새 질문 100
Refer to the exhibit. An engineer started to configure a router for OSPF. Which configuration must the engineer perform on the router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?

router(config)# router ospf 11router(config-if)# no passive-interface ethernet 1/1

router(config)# interface ethernet 1/1router(config-if)# no shutdown

router(config)# interface ethernet 1/1router(config-if)# ip ospf hello-interval

router(config)# interface ethernet 1/1router(config-if)# ip ospf priority 0

새로운 질문 101
You are writing an RPL scnpt to accept routes only from certain autonomous systems Consider this code.

If you apply this code to BGP filters, which effect does the code have on your router?

denies routes from AS 7070

allows routes from AS 7077

denies routes from AS 7007

allows routes from AS 770

새 질문 102
드래그 드롭
Drag and drop the OSPF area types from the left onto the correct statements on the right.
Select and Place:

섹션: 네트워킹

새 질문 103
Which configuration modifies Local Packet Transport Services hardware policies?

https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-1/addr_serv/command/reference/b_ipaddr_cr41crs/b_ipaddr_cr41crs_chapter_0111.html#wp1754734006

새 질문 104
전시회를 참조하세요.

While troubleshooting the OSPF adjacency between routers R1 and R2 an engineer noticed that both routers are stuck in the EXCHANGE/EXSTART state. What should the engineer fix to solve the ongoing issue?

IPv4 주소 일치

OSPF 영역 일치

OSPF 네트워크 유형 일치

MTU 값 일치

새 질문 105
전시회를 참조하세요:

An engineer is preparing to implement link aggregation configuration.
Which statement al about this configuration is true?

The switch port actively sends packets to negotiate an EtherChannel using PAgP

The switch port accepts LACP and PAgP packets from a connected peer and negotiate an EtherChannel using the common EtherChannel mode.

The switch port passively negotiates an EtherChannel if it receives PAgP packets from a connected peer

The switch port negotiates an EtherChannel if it receives LACP packets from a connected peer

새 질문 106
전시회를 참조하세요.

What is the effect of this configuration?

R1 supports a graceful restart operation on the peer, even if graceful restart is disabled on the peer.

R1 supports a peer that is configured for LDP SSO/NSF as the peer recovers from an outage.

R1 failovers only to a peer that is configured for LDP SSO/NSF.

R1 failovers to any peer.

새 질문 107
An operations engineer must implement IPv6 multicast leveraging the multicast group address FF70::/12.
Which two Cisco IOS XE configurations are needed to accomplish this task? (Choose two.)

Apply the ipv6 mid ssm-map enable and ipv6 mid ssm-map static commands only on the RP IPv6 router.

Apply the ipv6 pim command in all interfaces of all IPv6 routers in the IPv6 multicast domain.

Apply the ipv6 multicast-routing command in all IPv6 routers in the IPv6 multicast domain.

Apply the ipv6 pim rp-address command only on RP IPv6 router.

Apply the ipv6 pim bsr candidate rp command on the IPv6 routers that announce themselves as RPs and the ipv6 pim bsr candidate bsr command on mapping agent routers only.

새 질문 108
전시회를 참조하세요:

A network operator working for service provider with an employee id 3715 15:021 applied this configuration to a router.
Which additional step should the engineer use to enable LDP?

Disable Cisco Express Forwarding globally

Delete the static router ID

Enable MPLS LDP on the interface

Configure the both keyword to enable LDP globally

새 질문 109
Refer to the exhibit. The USER that is connecting an application on an Internet connection in AS
100 is facing these issues:
– The USER lost the connection to the application during a failure
between IG and R2.
– Router R2 configuration is lost due to a power outage.
– The application the USER is connecting to is hosted behind CE2.
What action resolves the issues on R3 and R4 routers?

Set R4 as a route reflector for R3 and CE2

Apply high Local Preference on R3 toward R1

Set R3 as a route reflector for R4 and CE1

Apply low Local Preference on R4 toward R2.

새 질문 110
전시회를 참조하세요:

Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?

The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family

The neighbor relationship is down because R1 believes R2 is in AS 65012.

The neighbor relationship is up

The neighbor relationship is down because the loco I-as value for R2 is missing in the R1 neighbor statement

새 질문 111
전시회를 참조하세요:

What does this value mean when it is received in XML?

It shows the ending of the script

It indicates a break in a sequence

It indicates a value assigned by a network administrator to tag a route

It means a data field is blank

새 질문 112

전시물을 참조하세요. show 명령 출력에 따르면 BGP 세션이 설정된 후의 결과는 어느 것이 맞나요?

IOS XR 라우터는 eBGP 이웃 192.168.2.2를 오가는 모든 경로를 광고하고 수락합니다.

IOS XR 라우터는 이웃 192.168.2.2에 대한 모든 경로를 알리지 만 다음 경로를 허용하지 않습니다.
192.168.2.2.

이웃 192.168.2.2에서 어떤 경로도 허용되지 않으며, 이 경로에 대해 어떤 경로도 알리지 않습니다.

IOS XR 라우터는 이웃 192.168.2.2에 대한 경로를 알리지 않지만 192.168.2.2의 모든 경로를 허용합니다.

섹션: 네트워킹
설명/참조:

새 질문 113
전시회를 참조하세요:

A network engineer is implementing a BGP protocol. Which effect of the local-as keyword in this configuration is true?

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 without additional configuration

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 without additional configuration.

The local-as keyword is used in BGP configurations to change the local AS number that is used in the BGP OPEN message when establishing a BGP session with a specific neighbor. In this case, even though the router is configured with AS 65000, it will use AS 65112 when establishing a connection with neighbor 192.168.1.2 due to the local-as keyword configuration. Reference := Cisco
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13761-39.html

새 질문 114
전시회를 참조하세요:

What is the effect of this configuration?

The two routers fail to form a neighbor relationship because their system IDs are different.

The two routers successfully form a neighbor relationship

The two routers fail to form a neighbor relationship because the authentication configuration is missing

The two routers fail to form a neighbor relationship because they have different ISIS area types.

새 질문 115
An engineer working for telecommunication company with an employee id: 3715 15 021 needs to secure the LAN network using a prefix list Which best practice should the engineer follow when he implements a prefix list?

An engineer must use non sequential sequence numbers in the prefix list so that he can insert additional entries later.

The final entry in a prefix list must be /32

An engineer must identity the prefix list with a number only

An engineer must include only the prefixes for which he needs to log activity.

새 질문 116
Refer to the exhibit. In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1, 2, and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

로드 중 …

Cisco 350-501 exam is designed for professionals who wish to validate their skills in implementing and operating core technologies in a service provider network. 350-501 exam is a part of the CCNP Service Provider certification and tests the candidate’s knowledge of advanced routing protocols, MPLS VPNs, QoS, and network automation. Passing 350-501 exam will demonstrate that the candidate has the expertise required to work with complex service provider networks.

TopExamCollection 350-501 Exam Practice Test Questions: https://www.topexamcollection.com/350-501-vce-collection.html