TopExamCollection NS0-184 dumps & NCSIE ONTAP Sure Practice with 60 Questions [Q28-Q52]

April 27, 2022 admin 0 Comments

4.6/5 - (16 votes)

TopExamCollection NS0-184 dumps & NCSIE ONTAP Sure Practice with 60 Questions

New NS0-184 Exam Questions| Real NS0-184 Dumps

NetApp NS0-184 Exam Topics:

Section	Objectives
ONTAP Configuration	– Describe how to add or remove nodes in an ONTAP cluster – Describe how to set up cluster peering – Describe how to implement security hardening – Describe support resources required for troubleshooting ONTAP installations
ONTAP Networking	– Describe how to configure ONTAP system networking – Describe network types used with ONTAP clusters
Customer Handoff	– Describe the tools available to review an installation – Describe the process for handover of new ONTAP cluster installation to the customer – Identify how to create documentation
ONTAP Concepts	– Identify how to update ONTAP – Identify ONTAP cluster controller components – Describe how to create aggregates – Describe the required steps for installation or expansion of an ONTAP cluster
ONTAP Switches	– Describe cabling of a switched cluster – Identify the software needed for cluster switch configuration

NO.28 You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.
Which three tools do you need to complete this installation? (Choose three.)

additional network cables

Phillips #2 screwdriver

laptop computer

slide rail kit

cable management tray

NO.29 You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches.
In this scenario.
Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

network port show -ipspace Cluster

network interface show -vserver Cluster

network device-discovery show -protocol cdp

network interface show -vserver Cluster -fields auto-revert

NO.30 You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?

You do not have network discovery enabled.

You do not have a static IP address.

You do not have IPv6 configuration set.

You do not have a default gateway set.

NO.31 You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.
In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)

term-based

perpetual

base

master

NO.32 After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.
In this scenario, which NetApp tool would have identified these errors after the installation process?

Cloud Manager

ONTAP System Manager

Active IQ Config Advisor

Active IQ Unified Manager

NO.33 You have an AFF A400 cluster that is running ONTAP 9.7 software. You are asked to set up FlexCache for NFS volumes.
In this scenario, which statement is correct when implementing FlexCache?

A capacity license is required.

A subscription license is required.

A site license is required.

No license is required.

NO.34 Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.
In this scenario, which two prerequisites should you examine in advance? (Choose two.)

Verify that the hard drives of the new controllers are compatible with the old controllers.

Verify that the existing cluster has a minimum 10 GB of free space for root volumes.

Verify that the existing switches support the additional controllers.

Verify that the platform of the new controllers can be mixed with the cluster’s existing controllers.

NO.35 Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.
Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

NO.36 Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)

Active IQ Config Advisor

Interoperability Matrix Tool

Active IQ System Manager

Hardware Universe

NO.37 When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?

RAID 4

RAID-TEC

RAID 0

RAID DP

NO.38 Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to install cross-site cluster management switches

to provide connectivity for NVRAM over iWARP

to enable SyncMirror replication

NO.39 A customer requires encryption at rest on every node root volume.
In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

NVE

IPsec

NAE

NSE

NO.40 What is the default shelf ID for disk shelves with IOM12 modules?

NO.41 After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.
In this scenario, which two commands would you use to accomplish this task? (Choose two.)

system node autosupport history show

system node autosupport check show

system node autosupport destination show

system node autosupport invoke

NO.42 You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?

Add the ASA controllers to an existing 4-node cluster with NAS licenses.

ASA controllers can only be added to clusters that have existing SAN licenses.

ASA controllers can only be installed as a standalone HA pair.

Add the ASA controllers to an existing 10-node cluster.

NO.43 Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

cluster ping-cluster

network test-path

statistics node show

NO.44 You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.
In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

NO.45 You want to use the NetAppDocs tool to collect information on a newly configured ONTAP 9.8 cluster and to generate a Word document with the details of the cluster configuration.
Which two data sources would you use to collect the necessary data? (Choose two.)

Active IQ Digital Advisor

Active IQ Unified Manager

ONTAP Cluster

AutoSupport packages

NO.46 Click the Exhibit button.

You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)

e0M

e0b-11

e0a-11

e0M-11

NO.47 What should you do to change the data protocol of a LIF?

Delete and re-recreate the LIF.

Add the new data protocol to the LIF.

Put the LIF in another broadcast domain.

Shut down the assigned port.

NO.48 You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.
In this scenario, what are three examples of data required from the customer? (Choose three.)

management IP addresses

cluster switch name

gateway IP address

BMC IP addresses

cluster name

NO.49 You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)

data switch cabling

cluster switch cabling

shelf connectivity

node CPU utilization

NO.50 You are using Broadcom BES-53248 switches for a cluster interconnect in a base configuration.
In this scenario, what is the minimum number of ISLs supported between the switches?

NO.51 Click the Exhibit button.

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?

Swap node1:e8a and node2:e4a.

Swap node1:e4a and node1:e8a.

Swap node2:e4a and node2:e8a.

Swap node1:e4a and node2:e4b.

NO.52 Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.
In this scenario, what would you tell the customer?