NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions [Q45-Q68]

October 15, 2023 admin 0 Comments

Rate this post

NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions

PDF (New 2023) Actual NACE NACE-CIP1-001 Exam Questions

NEW QUESTION 45
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

a recognized industry standard like SSPC-PA 2 that is broadly accepted

NACE 2/SSPC SP10

their best judgment based on similar projects and specifications.

a detailed checklist and document the lack of a standard.

NEW QUESTION 46
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?

1 cm (.39 inch)

2.5 cm (1 inch)

6.35 cm (2.5 inch)

2.5 millimeters (.10 inch)

NEW QUESTION 47
ISO SA 3 is directly equivalent to:

NACE No. 1/SSPC SP 5

NACE No. 2/SSPC SP 10

NACE No. 3/SSPC SP 6

None of the above

NEW QUESTION 48
Prior to using Inspection Tools the inspector must:

Ensure the instrument is within calibration parameters

Be trained on how to use the instrument

Read the manufactures’ instructions

a), b) & c)

NEW QUESTION 49
Relative humidity is

a measure of the amount of moisture in the air compared to saturation level.

a measure of the amount of moisture in the air compared to the air temperature.

the lowest temperature at which moisture forms on a steel surface.

the highest temperature at which moisture forms on a steel surface.

NEW QUESTION 50
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:

Pass/fail criteria

A final conflict resolution method

A general guide

A method to grade surface profile

NEW QUESTION 51
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners’ representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

Carefully review the document and do the best you can

Minimize your lack of understanding and go ahead with the inspection task to the best of your ability

Advise the owners’ representative of your lack of knowledge in this area

Hire a third patty to assist you in understanding the document

NEW QUESTION 52
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?

70% of the specified maximum thickness

80% of the specified minimum thickness

90% of the specified maximum thickness

100% of the specified maximum thickness

NEW QUESTION 53
Conventional spray is a good choice when:

High production rates are required

High quality finishes are required

High transfer efficiency is required

High viscosity coatings are being applied

NEW QUESTION 54
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:

Use another method as the comparator method is too subjective

Record the segment with the more aggressive profile

Record the segment with the less aggressive profile

Record your result by identifying two segments

NEW QUESTION 55
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:

Go with the majority opinion

Never change his/her mind

Achieve consensus through negotiation

Call the supervisor

NEW QUESTION 56
Stripe coats are best applied by:

Airless spray

Conventional spray

High volume low pressure spray

Brush

NEW QUESTION 57
ASTM Standards are applicable:

In the USA

In North America

In Asia

When specified

NEW QUESTION 58
The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

NEW QUESTION 59
SSPC SP 1 identifies the use of:

Organic solvents

Inorganic solvents

Biodegradable detergents

A wide variety of materials

NEW QUESTION 60
Removal of surface contaminants is done by:

Abrasive blasting

Waterjetting

A combination of methods

Scarifying

NEW QUESTION 61
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?

NEW QUESTION 62
NACE SP 0178 is a standard for:

Structural steel to be coated for Atmospheric Service

Tanks and Vessels to, be Lined for Immersion Service

Stainless steel pipe to be Externally Coated

Tanks and Vessels to be Externally Coated

NEW QUESTION 63
You are the NACE Inspector on a job where the Owner’s specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:

Skip the checks as you are. confident the blast pressure is OK

Skip the checks and just record the same readings as you have been getting

Keep doing the checks regardless

Keep doing the checks and consult the Owner’s representative for direction

NEW QUESTION 64
The main responsibilities of the inspector are to

demonstrate to the contractor how to apply the coating.

observe and direct the work of the contractors.

direct and perform the work stated in the specification.

observe and report the quality of the work performed.

NEW QUESTION 65
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

True

False

NEW QUESTION 66
Whenever dissimilar metals must join, the most common practice is to

provide cathodic protection to prevent corrosion,

provide anodic protection to prevent corrosion.

coat all connected dissimilar metals.

avoid coating all connected dissimilar metals.

NEW QUESTION 67
Fine cracks in the surface of a coating that rarely reach the substrate are called

cracking.

alligatoring.

checking.

blistering.

NEW QUESTION 68
Check abrasive blast pressure with a

needle pressure gauge

replica tape

surface comparator

nozzle aperature gauge

Loading …

The Coating Inspector Level 1 Exam covers a wide range of topics including surface preparation, coating application, inspection techniques, safety and environmental considerations, and documentation. It is designed to evaluate the competency of the individual in identifying coating defects and recommending appropriate corrective actions. NACE-CIP1-001 exam is a combination of multiple-choice questions and practical assessments that test the individual’s ability to apply their knowledge in real-world scenarios. Passing the Coating Inspector Level 1 Exam is a significant achievement and demonstrates a commitment to quality and safety in the coating industry.

Updated Oct-2023 Pass NACE-CIP1-001 Exam – Real Practice Test Questions: https://www.topexamcollection.com/NACE-CIP1-001-vce-collection.html

NACE-CIP1-001 Practice Tests

[Jan-2024] Latest NACE-CIP1-001 Exam Dumps for Pass Guaranteed [Q44-Q64]
NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions [Q45-Q68]

Related Certifications

NACE-CIP1-001