NACE NACE-CIP1-001 Exam Info and Free Practice Test TopExamCollection [Q58-Q77]

January 27, 2026 admin 0 Comments

5/5 - (1 vote)

NACE NACE-CIP1-001 Exam Info and Free Practice Test | TopExamCollection

Pass NACE NACE-CIP1-001 Premium Files Test Engine pdf – Free Dumps Collection

Individuals who successfully pass the NACE-CIP1-001 Certification Exam are awarded the Coating Inspector Level 1 certification. Coating Inspector Level 1 certification is recognized worldwide and is highly valued by employers in the coating industry. As a certified coating inspector, individuals have the opportunity to work in a variety of industries, including oil and gas, manufacturing, and construction. Coating Inspector Level 1 certification also opens up opportunities for career advancement and higher salaries.

QUESTION 58
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:

Accept the assignment without hesitation

Advise the prospective employer that you cannot accept the position

Meet with the prospective employer to determine the scope of your role

Review the NACE Attestation prior to making a decision

QUESTION 59
If inspectors identify issues of non-conformance during an inspection, they should

instruct the contractor’s personnel in how to correct the issue so the project is not delayed

perform additional tests secretly to ensure there are no other potential issues at the site

inform both the Contractor and the inspector’s supervisor so they can take appropriate corrective actions

wait until the final report is being prepared to identify the issues in writing so they are fully documented

QUESTION 60
An Inspector should change position when:

The Inspector is convinced by verifiable facts

Only when directed by the supervisor

The Inspectors position is not the majority position

The Owner can save some money by the change

QUESTION 61
Polymerization is the process of:

Monomers telegraphing

Monomers joining together

All thermoplastic coatings

All organic coatings

QUESTION 62
The main responsibilities of the inspector are to

demonstrate to the contractor how to apply the coating.

observe and direct the work of the contractors.

direct and perform the work stated in the specification.

observe and report the quality of the work performed.

QUESTION 63
Osmotic blistering is most likely to occur as a result of

inadequate anchor pattern/surface profile.

overcoating a surface contaminated with chemical salts.

airless spray application

applying tine coating too thin.

QUESTION 64
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

Chloride salt may produce a false positive

Synthetic oil or grease may not be identified

Ultra-Violet light may contaminant the surface

Presence of weld spatter may produce a false positive

QUESTION 65
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

Failing to determine the base metal reading (BMR)

Rotating the dial too fast when taking measurements

Taking measurements too far from the edge of a surface

Measuring ditty, tacky, or soft films

QUESTION 66
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:

telegraphing.

monitoring

juxtaposing.

transitioning.

QUESTION 67
A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required

Performing an adhesion test

When working on non-ferrous metals

QUESTION 68
To achieve consistently accurate results with ALL alt test equipment

wear gloves when sampling.

wash your hands before sampling.

avoid placing the sample discs on a surface.

calibrate the instrument in the field.

QUESTION 69
According to SSPC PA 2 a Spot Measurement is:

A single gauge reading

The average of gauge readings taken in a 4cm (1.5 inch) circle

The overall average of all readings

The average of all spot measurements in a given area

QUESTION 70
The NACE Inspector should perform tests for soluble salts:

Prior to surface preparation

After surface preparation

Prior to coating application

When specified

QUESTION 71
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:

Rust Grades A-D

Surface Conditions E-G

Rust Grades 1-4

Surface Condition H

QUESTION 72
ASTM Standards are applicable:

In the USA

In North America

In Asia

When specified

QUESTION 73
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

High Relative Humidity

Low Relative Humidity

High Surface Temperature

Low Surface Temperature

QUESTION 74
The initial steel condition is important to the NACE Inspector because:

If the steel is pitted more coating will be required

Less abrasive is need if the mill Scale s gone

It affects the final appearance after blasting

The Inspector may have to reject the Steel

QUESTION 75
Inspector’s daily reports are used:
Select All That Apply

By the contractor to estimate the amount of work done that day

To provide continuity between inspectors

To aid in arbitration between the contractor and client

To help in cases of a coating failure

QUESTION 76
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?

1 cm (.39 inch)

2.5 cm (1 inch)

6.35 cm (2.5 inch)

2.5 millimeters (.10 inch)

QUESTION 77
What is used to determine compressed air cleanliness?

Needle pressure gauge

Psychrometer

Blotter test

Profilometer

Loading …