第 19 号 Which statement about the AOS-CX VOQ feature is true?

NO.20 A network administrator accesses HPE Aruba Networking Central and notices that visitors consume too much internet bandwidth starving employee traffic when accessing an external service. Therefore, the administrator wants to limit wireless bandwidth to 60 Mops in both directions among all users in the voice rote and no more than 10 Mops in both directions for YouTube traffic. Deep packet inspection, web content classification, and firewall visibility are enabled.
Which configurations are required to accomplish this task? (Select two.)

第 21 号 Which data transmission method provides the most efficient use of airtime for VoIP traffic?

第 22 号 A customer reports that their HPE Aruba Networking ClearPass Guest captive portal is not functioning. The page loads but they are unable to browse after pressing connect. They have uploaded a valid and publicly trusted *. aruba-training.com certificate.
请参阅展品。


Which would explain this issue?

第 23 号 请参阅展品。


A network administrator is validating client connectivity and executes the show command shown in the exhibit. Which authentication method was used by the wireless station?

第 24 号 Which command would allow you to verity receipt of a CoA message on an AOS 10 GW?

NO.25 You have been tasked to ensure that audit logs on mobility gateways contain accurate timestamps, keeping security in mind. Which configuration change would best secure the time clock against attacks?

NO.26 Your customer is requesting a 4-ciass LAN queuing model tor QoS. Following best practices, match the PHB
/DSCP values to the application types.

NO.27

The ACME company has CX 8320 switches at the Services-Aggregation layer and CX 6200 switches at the Wired Access Layer. WiFi WLANs are deployed in an L2 model. After implementing IPv6 for wireless clients alongside IPv4, connectivity problems have increased.
What is the most efficient step to resolve this problem?

NO.28 A Windows device attempts to connect to an 802.1X network but it is not receiving the correct role. TEAP has been configured as the only authentication method in ClearPass. The wireless configuration is correct.
展览。

What is me most likely cause?

NO.29 展览。

A network administrator attempts to improve multicast traffic flow and performs some packet captures for validation What can the network administrator conclude from the results?

NO.30 A customer is evaluating device profiles on a CX 6300 switch. The test device has the following attribute:

* MAC address=81:cd:93:13:ab:31
The test device needs to be assigned the “lot-prod” role, in addition the “lot-default” role must be applied for any other device connected lo interface 1/1/1. This is a lab environment with no configuration of any external authentication server for the test.
Given the configuration example, what is required to meet this testing requirement?

第 31 号 In a campus topology using VSX with two aggregation switches and downlinks to access switches, which LAG interface configuration at the aggregation layer is correct based on the parameters below?
* ZTP VLAN 1001
* access switch MGMT VLAN 2002
* access switch MGMT VLAN is tagged
* connectivity to the access switch should be maintained before and after the ZTP operation is complete

第 32 号 A customer is planning to add loT devices that connect wirelessly to the existing 802.1X SSID. The customer will use HPE Aruba Networking ClearPass to authenticate the loT devices by MAC address but other devices will still need to authenticate by only 802.1X.
请参阅展品。

The customer provided the current configuration and reported their non-IoT 802.1X devices are no longer able to connect. Which configuration change can be made to fix the issue?

NO.33 展览。

You updated your gateway to me most recent firmware However after the firmware was updated, the gateway could no longer connect to HPE Aruba Networking Central. Your corporate ITIL procedures require you to implement your backout plan. You connected a console cable to your gateway and saw the following prompt.
Cpxload#
in what order, do you need to execute the following commands to return to the previous firmware version?

NO.34 A customer is evaluating device profiles on a CX 6300 switch. The test device has the following attributes:
* MAC address = 81:cd:93:13:ab:31
* LLDP sys-desc = iotcontroller
The test device is being assigned to the ”lot-dev” role However, the customer requires the “lot-prod” role be applied.

Given the configuration, what is causing the “iot-dev” role to be applied to the device’?